Positioning your niche at chest to eye-level is a good standard. This translates to a height of about 48 to 60 inches. Ideally, you’ll want to position your niche to fit between the studs which are usually located 16 inches apart. But many contractors can help you with planning the space for a more custom look.

Does a shower niche have to be centered?

I see no reason it needs to be centered. I would put it either on the same wall as the shower head, or on the back wall near the corner, to keep it out of the shower spray.

Can shower niche go on outside wall?

Generally frowned upon, installing a shower niche in an exterior wall is still possible.

How high should a shower niche be off the floor?

The standard shower niche height is between 36″ and 40″ off the shower floor (to the base of the niche). The typical or standard shower niche height for tub/ showers is between 25″ and 30″ (to accommodate bathers).

How high should a shaving niche be?

As a rule of thumb, the best height to install a shower niche is 1200mm from the floor. This puts your shower products at just the right height to grab and use easily.

Should you tile shower niche first?

This ensures any splashing or accidental spraying of water on the wall or shower door does not result in any seepage and water damage behind the tiles. If the niche needs to be tiled, then it has to be done tile by tile. … If the shower niche is large enough in height to add an additional level or compartment, go for it.

How far should shower head be from wall?

Answer: The best size for a rain shower head is 12 inches. This allows enough water to pour out without creating a flood.

How high should a corner shelf be in a shower?

In most cases, corner shelves work best when installed between 42” off of the base and “eye level”. When installing as a Foot Shelf, a comfortable height is about 9” to 12” off the shower base.

Is a shower niche a good idea?

A shower niche is a much better solution, for relatively little expense. It’s an extremely useful feature that provides you with a proper place to keep your shower accessories, without adding bulky organizers that take up much-needed space.

Does a shower niche need a lintel?

Whether the 600 mm is the vertical or the horizontal it does not matter the brickwork above will need to be supported, it is fair to say that you could remove the brick to create the niche and the brick above would not move, however over time it will, so please insert a lintel.

Article first time published on

Where should a ceiling shower head be placed?

Measure the height of the current shower arm, from the shower floor to the center of the arm. Then measure the height of the tallest person that’ll be using the shower. Shower heads should be installed at least a few inches higher than the height of the tallest user.

How long should the shower arm be?

Generally in the neighborhood of 2–3″. First off, the shower arm does not thread into the wall, but rather into a fitting behind the finished wall.

Which end of shower arm goes into wall?

Shower arms typically have a slight bend near their middle, and they almost always have threads on both ends. One end threads into a fitting called a drop-ear elbow inside the wall; the other end receives the showerhead, which simply turns onto the exposed end of the arm.

In what order do you tile a niche?

1. Step 1: Choosing Your Trowel. …
2. Step 2: Add the Sill. …
3. Step 3: Comb Thin-Set on Niche Back Wall. …
4. Step 4: Backbutter the Sill Tile. …
5. Step 5: Add Tile to Sill. …
6. Step 6: Laser Level the Sill. …
7. Step 7: Make the Sill Proud. …
8. Step 8: Level Each Sill.

How do you tile a niche without a bullnose?

Rail Molding: Some of these decorative moldings include pencil moldings, dental moldings, rail moldings, and cornice moldings. So if you don’t want a bullnose, you can use a rail molding of the same color, a complementary color, or even a different color that suits the aesthetic you want to achieve.

Can you tile shower niche?

There are two options when it comes to building a shower niche with a nice tile design, and it’s often confusing when it comes to knowing the differences between these two. … The main advantage of a tile ready shower niche (a preformed niche insert) is that it’s easier to install compared to custom niches.

Do shower niches get moldy?

When a custom niche is built well, it can look very sturdy, solid and deceptively waterproof. This is an assumption made far too often when shower niches are framed into the shower wall. … The rest you can imagine; moisture in the walls, which leads to mold, dry rot, etc.………. something you can easily avoid.

Where do corner shelves go in the shower?

Tile, vertically, up to the level where you want your shelf to be. A good rule of thumb is to place a shower corner shelf at about the chest-height of the average user of the shower, although you should choose the height that makes the most sense for you and your space.

Where should soap dish go in a shower?

The Soap Dish Tile The best place is on the same wall as the showerhead so that it sits behind the shower spray rather than in it. Ideally, the dish should sit 16 to 20 inches to the left or right of your showerhead if you have the room — or as far as you can install it to one side of the showerhead.

Can you put a shower niche in a single brick wall?

Re: Shower Niche help- single brick; can it be done? yeah you just need a double layer of waterproof plasterboard I think, which accounts for the cost.

Can you add a niche to an exterior wall?

Here’s how it works: Most exterior walls are 2×6 framing. I recommend buying a pre-made foam niche such as the Laticrete Hydroban niche, Noble Niche, or Schluter Kerdi Niche. A recessed shampoo niche from Laticrete is added in front of the foam increasing the r-value of this exterior wall.

How do you cover a niche wall?

Cut four 2-inch-by-4-inch lumber beams with a circular saw to match the height and width of the wall niche. Place all four beams into the wall niche, 1/2 inch from the edges of the niche’s border. This will allow the drywall patch to sit seamlessly inside the niche, covering it smoothly from the outside.

How do you Gyprock a niche?

1. 1Find the stud openings in the wall. …
2. 2Cut to locate the stud. …
3. 3Measure the height and width of the niche. …
4. 4Cut out the plaster. …
5. 5Install the niche. …
6. 6Apply the multi-purpose joint compound. …
7. 7Apply the second coat of the joint compound. …
8. 8Scrape and sand back the compound.

Where does the shower head go in a walk in shower?

Install wall-mount shower controls 48-52 inches above the floor; place the controls so they are accessible from inside and outside the shower. Mount showerheads 69-72 inches above the shower’s floor. Keep in mind that sprays from traditional showerheads extend as much as 4 feet.

How far does water splash in the shower?

70% of water used in a shower, falls within 600mm of the shower head. It’s for this reason that you need to take the splash area into consideration. Effective management of your splash area reduces water wastage and prevents your shower from dispersing water all over the bathroom and soaking anything in its way.

Are rain shower heads worth it?

Rain shower heads won’t give as good water pressure as a standard shower head. I’ve used a few rain shower heads in hotels and they do offer good pressure, but not as good as a standard shower head. The benefit of a rain shower head is more water flows over the body as it has a wider area of flow.

How high should spout be above tub?

The tub spout will generally be located 4 inches above the rim of the tub. In a shower only unit, the faucet is placed higher at 48 inches off the floor.

Do shower arms come in different lengths?

Available in four different lengths, with or without an escutcheon, we’re confident these shower arms will suit your standard installation just fine.