Where can I get a Kenmore water softener serviced?

You can trust WaterSmart to service your Kenmore water softener in Southern Ontario, as we have been proudly servicing Kitchener, Waterloo, Cambridge and Guelph for 25 years. This guide will give you solutions to some of the most common problems you might encounter, as well as maintenance and service tips.

Where is the rotor valve on a Kenmore water softener?

You should contact a professional to do this for you. The rotor valve directs water through your water softener during the water softening cycle and while flushing the resin filter. The rotor valve seal is located on the bottom of the rotor valve.

Why is my Kenmore water softener getting salty?

Another reason why you may be getting salty water is that your float levels may be too high. If this happens, then too much water will be filling up your brine tank. Check your float levels and see if they are set too high. If they are, adjust them to a lower level.

How do you turn off a water softener?

Before your begin, turn off the water supply to your water softener. It will often look like an outdoor faucet. Turn it completely to the right to shut off the flow of water. The water line connects your water softener to your water source. If the line has become loose, you may get water dripping from it.

You can trust WaterSmart to service your Kenmore water softener in Southern Ontario, as we have been proudly servicing Kitchener, Waterloo, Cambridge and Guelph for 25 years. This guide will give you solutions to some of the most common problems you might encounter, as well as maintenance and service tips.

Why does my Kenmore water softener keep leaking?

Solution: This is often caused by a tiny vacuum leak somewhere, probably in some rubber part. Another common problem is that an O-ring slips off or gets damaged. In both of these scenarios it is probably best to contact a local water softener repair shop, like WaterSmart, to come to your house and fix the issue.

You should contact a professional to do this for you. The rotor valve directs water through your water softener during the water softening cycle and while flushing the resin filter. The rotor valve seal is located on the bottom of the rotor valve.

Why is my Kenmore Salt Tank half full?

Solution: The most common reason for the salt tank being half full of water is that the nozzle and venturi are dirty or blocked. This is a process that Kenmore provides instructions on how to do on your own at

What is error code 3 on Kenmore water softener?

Kenmore Error Code #3: If you are getting an Error code 3, it may be that the switch (pictured below) needs replacing. Here are the steps to replace this switch: Step 1: Unplug the unit. Step 2: Remove the lid of your softener so you can see the motor.

Where is the float on a Kenmore water softener?

This could be happening if your safety float is sticking. Step 1: Remove the lid of your water softener. Step 2: Remove the lid off of your salt level indicator tube; your safety float is located inside of this cylinder. Step 3: Pull out your safety float mechanism that is inside of the cylinder.

Can a plumber fix a Kenmore water softener?

Unless you are a plumber by trade you probably waste a lot of time trying to troubleshoot the issue. In contrast, a professional who deals with these issues on a daily basis would most likely be able to fix the issue quickly and for a low cost.

Where can I buy Kenmore water softener in Ontario?

Since Sears has closed and you can no longer take your product directly into a store for maintenance or repair, we can help. You can trust WaterSmart to service your Kenmore water softener in Southern Ontario, as we have been proudly servicing Kitchener, Waterloo, Cambridge and Guelph for 25 years.

Kenmore Error Code #3: If you are getting an Error code 3, it may be that the switch (pictured below) needs replacing. Here are the steps to replace this switch: Step 1: Unplug the unit. Step 2: Remove the lid of your softener so you can see the motor.

Why is the timer on my water softener not working?

The timer is an electronic control board that allows you to program your water softener and lights up the display. It also controls the water softening and resin filter flushing processes. If it isn’t working, it will need to be replaced. Step 1: Put on work gloves and unplug your water softener from its power source.

What are the parts for a Kenmore water softener?

We have Kenmore Ultrasoft 280 parts as well as Kenmore 350 Series water softener parts. Look up the Sears water softener parts you need on our convenient parts list diagrams for your model.

Why does my Kenmore water softener stop working?

When your water softener stops working, get the Kenmore water softener parts you need to fix the problem at Sears PartsDirect. Lack of electrical power, a failed power transformer or a faulty timer can prevent the water softener display from lighting up.

How long is the Kenmore water softener good for?

Unfortunately, the Kenmore water softeners do not have a very long warranty as their warranty is only good for 1 year from the date of purchase for any defects, with the exception of leaks that the warranty covers for 10 years on most models.

What’s the best way to test a Kenmore water softener?

Step 1: Unplug your softener and then plug it back in. Step 2: Your softener will go through a test mode; it usually takes about 8 minutes to go through this. This may solve your problem.

How does the Kenmore 300 series water softener work?

Kenmore 300 Series Water Softener – High Efficiency Model 38300. This unit comes with something called “IntelliSoft2”. This feature allows the unit to use up to 20% less water and 32% less softening salts. Its automatic salt tank light (LED) informs you when and if the tank needs replenishment with new softener salt.

Solution: This is often caused by a tiny vacuum leak somewhere, probably in some rubber part. Another common problem is that an O-ring slips off or gets damaged. In both of these scenarios it is probably best to contact a local water softener repair shop, like WaterSmart, to come to your house and fix the issue.

What does error code 1 on Kenmore water softener mean?

Error code #1, meaning a valve motor failure, is one of the more common codes you will have displayed. If your Kenmore water softener display is showing Error Code #1, you can try the following: Step 1: Unplug your softener and then plug it back in.

What’s the model of the Kenmore 800 water softener?

I have a Kenmore 800 water softener Model No 625.75190 When I plug the softener in the motor constantly runs cycling – Answered by a verified Plumber We use cookies to give you the best possible experience on our website.

Why is my Kenmore water softener not draining?

These include: If your water starts to taste salty and there is brine coming through your lines and plugging up your faucets, your water softener tank may be flooded and not draining properly. This could be happening if your safety float is sticking. Step 1: Remove the lid of your water softener.

How long is the warranty on a Kenmore water softener?

Here is a link to just one sample of the manual of a Kenmore Water Softener, you will see right on page #2 of the document that it states the warranty is only 1 year. This is standard across all Kenmore models. Below are some more links to warranty’s of some of the top models.

These include: If your water starts to taste salty and there is brine coming through your lines and plugging up your faucets, your water softener tank may be flooded and not draining properly. This could be happening if your safety float is sticking. Step 1: Remove the lid of your water softener.

How does the Kenmore 300 series water softener save you money?

Kenmore 300 Series Water Softener – High Efficiency Model 38300 This is another high efficiency model very similar to the Kenmore 41,000 grain water softener. Apart from providing you with high quality soft water it saves you money too. How? Well, it saves you money because you will use less salt and electricity.