This setting is used infrequently, but is helpful when you want to mix newly added pool chemicals or when you need to keep the pool water moving while you perform filter repairs.

Should I run my pool pump on filter or recirculate?

You should run your pump/filter as long as it takes to keep the pool clean. Some pools have great circulation combined with low use, therefore run times can be quite short. Other pools have lousy circ systems and huge bather loads and even 24/7 filtration has trouble keeping up.

Can I shock my pool on recirculate?

Recirculate will allow the shock to mix quickly and start working. Be aware when using the Recirculate setting, the pool won’t be filtering out debris and algae, so it will remain in the water and on the bottom of your pool until you filter or backwash it away. The Recirculate setting bypasses the pool’s filter.

How many times should I circulate my pool water?

It is recommended that you “turnover” or circulate all of your pool water through the pool filter at least once throughout the day. This will ensure that the chemicals are evenly distributed and your water stays clean and clear.

What setting should my pool filter be on?

The lever should be on the ‘Filter’ setting most of the time. This is the setting that provides normal pool filtration by pushing the water through the filter media (sand, glass beads or D.E) that then traps any dirt and debris before the water is returned to the pool.

What does backwash do on a pool filter?

The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value’s waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.

Do you vacuum a pool on backwash or waste?

Don’t use any metal object that can rust as a weight. 8. Vacuuming pool with filter valve in “backwash” position. When a pool is vacuumed with the sand filter valve in the “filter” position, the dirt and debris that passes through the pump ends up inside the filter on top of the bed of sand which is where you want it.

How do I increase circulation in my pool?

To ensure proper circulation, you need to switch on the pump for at least 8 hours a day. This ensures the pool circulation is effective. Make sure you size the pump, i.e: get a pump according to your pool volume. If your pool capacity is 10,000 gallons, then you need to divide 10,000 by 480 (8 hours x 60 minutes).

What makes the water circulate in the pool?

How Does It Work? In a pool circulation system, water is drawn from the pool through skimmers and drains by a centrifugal pump. … The pressure created by the pump’s impeller forces the water through a filter which intercepts any debris not caught by the baskets.

Is it bad to run your pool pump 24 hours a day?

Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. … If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

Article first time published on

How long should the pool circulate after adding chlorine?

Generally you will want to wait at least 4 hours, but ideal is waiting for one complete turnover of the water (the time it takes all the water to go through the filter).

What is good rpm for pool pump?

Suction cleaners typically run at around 2200-2400 RPM. Heaters require 20 to 40 Gallons Per Minute (GPM) so might run at around half speed or a little higher. You would probably want to run your Spa at up to full speed, 3450, for maximum effect.

Should you rinse after backwash?

Backwashing reverses the flow of water, lifts up and flushes the sand, and then expels the dirty water via a waste line into the ground or drain. In order to prevent residual blow back into the pool, once you’ve finished backwashing it’s highly advisable to rinse the filter.

What's the difference between backwash and waste?

Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter.

Do you remove skimmer basket when vacuuming to waste?

Make sure to empty all skimmer baskets. If you vacuumed on waste, you will need to turn your filter to the “rinse” setting, turn on the pump and let it run for about 30 seconds, and then turn the pump back off. Make sure to set your filter back to “filter” after you do this.

How often should you backwash a pool?

As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.

Do you leave skimmer basket in when vacuuming pool?

You need to leave the skimmer basket in under the skim vac plate, this allows the skimmer basket to catch your debris, and you can empty it quickly without having to turn your pump off and on like you would without it.

How often do you backwash de filter?

Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. “When do we need to backwash?” – It is recommended to backwash your filter once every 4-6 weeks of regular use.

Can you backwash a pool too much?

Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.

Why is the pressure high on my pool filter?

The most common cause of high pressure in a pool is a dirty filter. Take cartridges as an example, as the material sives dirt from your pool water, the cartridge fabric more and more clogged. The clogging means the water has fewer and smaller perforations in the filter media to squeeze through.

How do I circulate my pool without electricity?

If you still have electricity, you can use a robotic pool cleaner or a submersible pump to clean, move and circulate the water. If you are without power, grab your pool brush!

How do you check pool circulation?

To observe a pool? s circulation, try the ping-pong ball test. This involves tossing at least a dozen ping-pong balls into the pool and watching where they travel. The balls should travel in a clockwise pattern and eventually end up in the skimmer basket.

Can I leave my pool pump off for a week?

Yes you can turn your pool pump off for a week. You can turn it off for a month, but there are consequences. The pool will get dirty—no pump, no filtering. The chemicals will not circulate and the water could start turning a nice shade of green as algae forms.

Do pool pumps use a lot of electricity?

Outside of the air conditioner, the pool pump is the largest electricity consumer in the average pool-containing home. According to the study, at the national average of 11.8 cents per KWh, a pool pump alone can add as much as $300 a year to an electric bill.

Do you run pool pump while raining?

We recommend that our customers run their pumps rain or shine UNLESS we have an electrical storm. In that case, lightning could strike an outside circuit, which could damage your pump and other equipment. If you’re worried about lightening, turn the pump off or shut off the breaker.

How long does it take for pool chemicals to circulate?

If you add chemicals to balance the water after testing, wait a full day – or even longer – before retesting. It takes about 24 hours for the chemicals to properly circulate in order to get an effective reading from the retest. The water test will assess the pH, chlorine, total alkalinity and calcium hardness.

How long should you run your pool pump after adding chemicals?

In the industry it is recognized to have the pool run for 3 hours at a bare minimum up to 24 hours. 24 hours really is overkill but it’ll ensure the water is completely mixed with the chemicals.

Should pump run when shocking pool?

Shocking your pool is a fairly simple process. … Pour the mixture from the bucket into the water around the edges of the pool. Let the pump run for about 6 hours or more and test the water. Don’t use the pool right away – wait for the free chlorine levels to drop to 1 – 3 ppm before it is safe to swim.

What is quick clean on pool pump?

The pump is equipped with a Quick Clean feature, which can be engaged to temporarily run at higher or lower speeds ranging from 300 to 3450 RPM. At the end of a Quick Clean cycle, the pump will automatically return to the appropriate point in its programmed schedule.

Can you backwash with filter balls?

Yes, you save water with FilterBalls with the backwashing. … Simply follow the FilterBalls installation instructions by noting your filter pressure upon installation and backwash when the pressure increases by 5-6 psi. Note your starting pressure will be much lower than what you experienced with sand.

At what PSI should I backwash?

A good rule of thumb is to backwash once the pressure displayed on your pressure gauge is 8-10 psi over the starting level. Backwashing after heavy rains, treating for algae, or when trying to clear cloudy water will keep your filter working efficiently.