In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter. However, using a diamond blade is recommended as laminate can be tough to cut through and may damage another type of blade. Typically, you will cut with the finished side up.

What kind of saw is needed for laminate flooring?

In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter. However, using a diamond blade is recommended as laminate can be tough to cut through and may damage another type of blade. Typically, you will cut with the finished side up.

Do I need a Mitre saw for laminate flooring?

The jigsaw will be much slower than a circular saw or miter saw though so keep this in mind and it will usually burn through a good amount of blades. you will want to use either a medium or fine toothed jigsaw blade to cut the laminate flooring, making sure the exposed side is up while you are cutting.

What's the best hand saw to cut laminate flooring?

• Sharp GT-toothing for long-lasting sharpness and a straighter, faster cut – 11 TPI.
• 2 component handle for extreme grip and comfort.

Can I cut laminate flooring with a miter saw?

The easiest saw to use for cutting your planks to length is a power miter saw, or chop saw. These saws are available with 8- to 12-inch diameter circular blades. You can cut the material in one motion, and the fence aligns the material to the blade for a perfect cut every time.

Can a 10 inch miter saw cut laminate flooring?

Makita A-93681 10-Inch 80 Tooth Micro Polished Blade 091 inches thick, allowing the blade to cut through flooring materials such as laminate with little resistance or strain on the saw’s motor.

Can I use a hand saw to cut laminate flooring?

Sawing your boards can actually be done with a regular handsaw. Make a small cut first and then saw on! It’s ideal for shortening laminate boards. Some tips to make it easier: put your saw line as close as possible to your bearing surface and don’t forget to firmly hold the piece you’re sawing off.

Does laminate flooring dull saw blades?

You see, laminate flooring will destroy a wood cutting blade with alternating top bevel (ATB) teeth in no time at all. The sharp points on this type of blade can’t handle anything that hard – they dull quickly and those tips are what the blade uses to cut cleanly through wood.

What does a toe kick saw do?

ideally if existing flooring or plywood being removed runs under cabinets or drywall. Additionally, toe kick saws are used for underlayment removal often found in kitchens that may have vinyl floors installed above.

Can you cut laminate with a utility knife?

Plastic laminate is a durable, waterproof covering often used for kitchen and bathroom countertops. … You can use several tools to cut laminates, including a table saw or handheld power saw, a utility knife, a router or a hand slitter. The best cutting approach depends on whether you’re rough cutting or finishing edges.

Article first time published on

How do you cut Wilsonart laminate flooring?

1. Measure the laminate with a measuring tape. …
2. Transfer the measurements for the strips to the back of Wilsonart or Formica laminate. …
3. Install a fine-toothed blade on your table or circular saw. …
4. Cut the Wilsonart or Formica laminate into strips with a table or circular saw.

Can I use a table saw to cut vinyl flooring?

A table saw can certainly be a very useful tool to cut vinyl planks, especially when performing a rip cut. Essentially, a rip cut is when you cut the planks along the length of the plank. This would mostly be done where the vinyl planks meet the wall on their long edge.

Can you cut tile with a toe kick saw?

795 Toe-Kick Saws. It is a 2 5/8″ diameter continuous rim dry cutting diamond blade for cutting ceramic tile, brick, concrete, stone, or for removing grout. It cuts to a fixed depth of 3/8″ using the saw. For best results, cut 6 feet maximum, then allow cooling.

Can I cut laminate flooring with a Stanley knife?

Can You Cut Laminate Wood Flooring With A Utility Knife? Yes. You can cut laminate wood flooring with a utility knife. … A Carbide Tipped Blade or Carbon Steel Blade is best for cutting through laminate flooring.

What kind of blade do you use to cut laminate countertop?

Cutting a post-form laminate countertop to length requires a clean, straight cut. The best DIY tool for the job is a circular saw with a fine-tooth carbide blade made for laminate (the same blades are typically sold for non-ferrous metals and other types of plastics). You can also use a jigsaw with a fine-tooth blade.

Do you cut the tongue off the first row of laminate?

Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. … If it is too short, cut a new plank in half and use one half to start the second row.