Let’s start with 15 gauge finish nailers. These tools are ideal for projects such as cabinet and furniture building, picture frame assembly, trim and molding installation, and upholstery trim applications. Look for an angled nail magazine on most 15 gauge finish nailers.

Which is better 15 or 16-gauge nailer?

The main advantage of a 16-gauge gun is that it’s smaller and lighter. If you’re shopping for a finish nailer, I’d recommend the larger 15-gauge gun, simply because the fatter nails provide more holding power. … You’ll pay about the same for a name-brand 16-gauge nailer as you would for a 15-gauge gun.

What can you use a finish nailer for?

A finish nailer is the best all-around nail gun for most non-structural types of projects. As their name implies, they’re typically used to finish the job. Here’s some common projects where a finish nailer excels: Installing baseboard, crown molding, chair rails, and other types of trim.

Can you use 15 gauge nails for baseboards?

What gauge nails to use for baseboards? Based on nail size, you should be looking for anything between 15 gauge and 18 gauge. With these gauges it you can easily find nails up to 2.5” long which is an ideal length for baseboard nails.

What is the difference between 18 gauge and 15 gauge nails?

The higher the number, the thinner the nail; the lower the number, the thicker it is. … One advantage to 15-gauge nails is that they are collated at an angle, which allows the nose of the nailer to reach into tighter spaces. Brad nailers use smaller 18-gauge nails up to 2 inches long.

What size nails do I use for door trim?

The 15-gauge nails, ranging in length from about 1-1/4 in. to 2-1/2 in., are strong enough to secure door jambs and other heavy trim materials. Plus, the angled nose on most 15-gauge nailers allows you to nail in corners and drive toenails more easily.

What kind of nail gun do I need for baseboards?

A finish nailer is a versatile tool, and drives either 15- or 16-gauge nails. They are used for smaller projects than framing nails, such as crown molding, baseboards, cabinets, chair rails, decorative trim, millwork, and hardwood flooring.

What size nails should I use for framing?

Nail size is more important than you might think when framing interior walls. Nails that are too long or fat are difficult to drive and can split wood, while short or thin nails just don’t do the job. The best nails for framing are 3 1/2 inches long. These are called 16-d, or “16-penny,” nails.

What size nails should I use for quarter round?

Attaching Quarter Round Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well.

What is 16 gauge nailer used for?

The 16-Gauge Nailer is Versatile Carpenters use them for a wide variety of tasks including interior trim, baseboard, and crown. You can do stair risers with them, and they’re a good option to nail down tongue and groove flooring like near a wall or in a closet where a flooring nailer won’t work.

Article first time published on

Can you use 16 gauge nails for framing?

Now, for the most part, 16 gauge nails, typically 3 1/2 inches long are the best to use when it comes to framing projects. These are technically called 16-d (or “16-penny”) nails and you often have two choices when framing: common nails and sinkers (forget the rest!).

What are 16 gauge nails used for?

1. Crown and base moldings.
2. Flooring.
3. Cabinets.
4. Casings.
5. Staircases.
6. Exterior trim.
7. Chair rails.

Should I use brad nails or finish nails for baseboards?

The added thickness means that finishing nails create a stronger hold than brads. This makes them useful for heftier applications with thicker material, such as cabinets or baseboards. … Because they are thicker than brad nails, finish nails are more likely to split thin or delicate pieces of wood trim.

Which is better brad nail or finish nailer?

While the downside to a brad is its holding power, finish nails are made from heavier 15- or 16-gauge wire, which means they can handle a greater payload. For larger trim, such as baseboards or crown molding, a finish nail is the more suitable choice.

Which is better straight or angled finish nailer?

Angled nailers are usually made with less material – this often means that they are also lighter in overall weight as well. However, this may not always be true if the magazine for a given nailer is full (thicker nails obviously weigh more). In general, though, angled nailers are more portable and easier to store.

Can I use a brad nailer for framing?

Finish Nailers and Brad Nailers They are most often used for installing wood trim, where the nail heads will visible. These are versatile tools for a homeowner to own, quite affordable in cost and useful for a variety of purposes—they will work for light framing work, too.

Do all nail guns require a compressor?

While no nail gun requires a specific compressor, each has specific air requirements. Nail guns operate between a range of pressures measured in pounds per square inch (psi). In addition to pressure, nail guns require a minimum volume of air for correct operation. This volume is rated in cubic feet per minute (cfm).

What type of nail gun should I use for shiplap?

A finish nailer or brad nailer is the easiest and most efficient tool to use when installing your new shiplap or tongue and groove. They can be purchased/rented relatively cheaply from your local hardware store, they’re lightweight, and are simple enough that a 12 year old can use them!

Can you hammer in finishing nails?

Avoid scratches or hammer dents by using a nail set to finish driving the nail. Use a nail set that is the same diameter as the finishing nail. Center it on top of the nail and hit it with the hammer. Continue hammering until the nail is about 1/8-inch below the surface of the wood.

Can I use brad nails for baseboard?

You can use a brad nailer to attach baseboards to the wall, though sometimes a finishing nailer might be best. Brad nails are smaller and thinner, ideal for delicate pieces of trim. Finish nails are thicker and have a stronger grip, typically the better choice for tall and long pieces of a baseboard.

Can you use a nail gun on drywall?

Drywall is not normally applied with a nailer. Finishing it requires the fastener be set below the surface of the board so the mud can skim it flush, and nailguns aren’t good at this. Normally you use screws and a screwgun.

What size nails are used for shoe molding?

If you’re wondering “Which nails should I use for shoe molding?” the answer is 2″ brad nails for the nail gun. Try to find smaller finishing nails for your hammer so they’re not so noticeable on the shoe molding.

Should you glue or nail quarter round?

A: Quarter-round should be nailed to the base boards only. It is intended to hide gaps between the base and floor. It should also permit a little movement in the flooring. Plus, it absorbs the impact of feet and furniture legs, so you may want to replace it sometime—thus, don’t glue it.

Can I use a brad nailer for quarter round?

For the most part, the best tool for nailing quarter-round is a brad nailer. Brad guns shoot thinner nails from the smaller 5/8-inch to 2-inches, which are fine for attaching light moldings such as quarter rounds – you don’t want to split the molding or leave visible holes.

How long should brad nails be?

Having the right length of brad is crucial for a good result. The rule is simple: a brad should be three times as long as the thickness of the material you are fixing. Example: if the material is 15 mm thick, the brad should be 45 mm long. Choose a brad gun that takes the length of brad you need.

Should you use screws or nails for framing?

Nails are often preferred for structural joining, including framing walls, because they are more flexible under pressure, whereas screws can snap. Nails are also called upon when securing plywood sheathing for exterior walls, installing hardwood floors, and attaching siding and roofing.

How far should a nail penetrate?

Rule of Thumb #2 – Use a nail that will penetrate the item you are nailing to (not through) at least 3/4″. So, to use the same example of 1/2″ sheathing you would need a nail that is 1 1/4″ long. 3/4″ + 1/2″ = 1 1/4″.

What nails to use to build a shed?

For the substructure and framing of your shed where nails are hidden you should use coated nails such as vinyl coated sinkers or cement coated nails. These bond to the wood and will not pull up as easily and readily as uncoated nails.

Is 16 or 14 gauge better?

The thicker the wire, the lower the gauge number. … For long wire runs, high power applications and low impedance speakers, thick wire (12 or 14 gauge) is recommended. 16 gauge wire is usually fine for short runs less than 50 feet.

What's the best nail gun for fencing?

PRODUCTFEATURESMetabo HPT Cordless Framing NailerJob Type: Framing Power Type: Cordless Battery Warranty: 1 yearCheck The Price!Bostitch Round Head Framing NailerJob Type: Framing Power Type: Pneumatic Warranty: 7 yearCheck The Price!

What's the difference between a brad nailer and a pin nailer?

For starters, brad nailers use a much larger 18 gauge nail. This nail has a much larger diameter head, which is why a brad nailer leaves a visible nail hold that must be covered with putty. What is this? Pin nailers, on the other hand, use a smaller 23 gauge nail.