What does error code 14 mean on Rinnai?

Error code 14 has no troubleshooting steps and Rinnai recommends the issue be addressed by a qualified technician. Error code 14 indicates a remaining flame safety device. This means the flame safety device on your hot water system has been triggered and will prevent water from being heated.

What is the error code for Rinnai Water Heater?

Each Rinnai unit uses a temperature controller (either MC-91-1 or MC-91-2) on the front panel to display various configuration options for installation as well as error codes for when problems arise. The previous nine error codes are stored in memory.

How to clear an error code on a Rinnai split unit?

After unplugging the AC unit, wait for a few minutes before plugging the unit back into power. After a few minutes, plug the unit back in and turn on power. This “Error Code Reset Procedure”may help to reset the control board (computer)and clear the error code or flashing lights from your Rinnai Split System AC Unit.

What does error code 63 mean on Rinnai?

Error Code 63 What it Means: Circulation flow rate dropped below 1.3 gpm. How to Fix: Use temperature controller to display flow rate (hold UP for 3 seconds and press the ON/OFF button).

Where is the model number on a Rinnai wall furnace?

The model number is printed on the top of the rating plate located on the right side of the unit. The recall includes only those units manufactured from February 2000 through December 2007. The manufacturing date code is the first four digits of the serial number, written as YY MM, and is located at the bottom of the rating plate.

Why does my Rinnai Water Heater have code 10?

 Remove burner and inspect copper fins in heat exchanger for a build up between fins.  This will cause air flow restrictions which can lead to code 10’s.  If build up is present, you will need an air compressor capable of delivering 120 psi of air to blow out the burner and heat exchanger fins.

Are there any recalls on Rinnai natural gas furnaces?

Incidents/Injuries: Rinnai has received 11 reports of carbon monoxide leaking from the furnace. No injuries have been reported. Description: The recall involves Rinnai EnergySaver Direct-Vent Wall Furnaces, Models RHFE 431 and RHFE 556. They are either natural gas or LP gas (propane) fueled. The following model numbers are included in the recall:

How long can you run code 14 propane?

This code 14 comes in instantly, you hear the woosh of the propane igniting and then almost instantly the code 14 hits, it doesn’t have time to get hot never less going over tempature the failure is more frequent that before but when it does work, it works great and you can run it for 30 minutes solid with no problem.

Why is there an error code on my Rinnai Water Heater?

If your Rinnai displays an error code 05, you need to restart the water heater and open the hot water faucet. This code is not observed on all Rinnai water heaters. Measuring the resistance of the bypass flow control can help in determining the problem. If the error code persists, you may need to replace the bypass servo.

When do you get error 16 Rinnai gas boiler?

Error 16 characterizes overheating in the system when the temperature of the coolant is more than 95 degrees and lasts for 3 seconds or more. In this situation, you must: Be sure to check the pump’s performance. Error 17 indicates a water leak and occurs after 3 water make-up signals.

What to do when your Rinnai tankless says error code 02?

If your tankless is displaying and error code 02, you’ll need to call a professional. If there was a power outage or interruption its possible that once the power is restored the water won’t flow. When this happens, try the following: Shut off all the hot water fixtures in your house. On the temperature controller, press the on/off button twice.

Why do you need a Rinnai tankless water heater?

Rinnai Tankless Water Heaters last up to twice as long, have twice the warranty, and save energy as they only heat water when it is needed. Plus, you never have to worry about running out of hot water with a Rinnai Tankless Water Heater because it keeps heating as long as it is needed.

What type of regular maintenance does a Rinnai tankless water heater require?

There are two types of periodic maintenance that your service technician should perform to keep your Rinnai tankless water heater in top shape. It’s important to note, the time in between necessary maintenance will depend on the water quality in your home. 1. The in-line screen filter should be checked periodically for debris and cleaned.

Does a Rinnai tankless water heater have a standing pilot?

In the event of a power outage, the Rinnai unit will not operate. This is because Rinnai Tankless Water Heaters do not have a standing pilot light. They operate with an electronic ignition.

How does the Rinnai tankless water heater work?

The Rinnai tankless hot water system uses a gas-fired heat exchanger to heat water on demand. The innovative tankless technology heats water only as needed when water flow is detected, resulting in continuous hot water.