What does E3 mean ON WAVE spa?

The E3 Error indicates a condition where the Temperature Sensor has sensed a high temperature (Greater than 113 F. / 45 C.) within the PCU before the water has passed through the Heater. E3 will disable all functions and requires the PCU to be Reset (see solution) to clear once the temperature is within safe use range.

Why does my hot tub keep tripping out?

Hot tub heaters can become corroded or damaged, resulting in a circuit breaker that keeps tripping when you want to use your hot tub. You might be able to notice signs of damage or corrosion in this part of your hot tub. If the heater does have damage, you might need to have it repaired or replaced.

How do I fix error code E03 on a lazy spa?

E03

1. Remove the pump from the spa by placing the stopper caps on the inside of the spa over the debris screens.
2. Carry the spa pump indoors or to a warmer place.
3. Leave this within a warm area for 2 to 3 hours for the internal parts to warm up.
4. Once the spa pump has warmed up, the error code should disappear.

How long can you stay in a hot tub at 102 degrees?

Recommended Time in a Hot Tub Pregnant women, for example, should never get into a hot tub that is over 102 degrees. Even at cooler hot tub temperatures, they should limit their time to under 10 minutes.

What does E5 mean on a wave spa?

E5 – PROBLEM: High water temperature indicator, All functions do not work, beeping warning, The filled water is over 50°C(122°F) – SOLUTIONS: Unplug the Control unit and contact your dealer for service. E6 – PROBLEM: Water pressure is not high enough to activate heating, Not heating and filtering properly.

Should I leave my wave spa on all the time?

Can you leave the spa unattended while it’s heating up? You can leave Spa unattended as the heater will switch off automatically when it reaches the set temperature. Make sure the spa is connected to an electrical outdoor socket designed specifically to protect it from water.

What does code E02 mean on lazy spa?

E02 ERROR CODE REASON WATER LEVEL IS NOT CORRECT. The water flow sensors will not detect the water properly if the water is below the minimum line. on the spa liner.

What to do if your hot tub has an E11 error code?

Gradually add and dissolve 0.5kg (500g) of Pure Spa Salt at a time. Start the Salt Chlorinator System. Allow the spa pump to run on either the 5 hour or 8 hour setting. If the E11 error code is visible again, place a further 0.5kg (500g) of Pure Spa Salt in the spa. Water Leakage.

What should I do if my spa water is 107°F?

One of the sensors has detected that the spa water is 110°F. Remove spa cover and let the water cool down. At 107°F the spa should reset. If spa doesn’t reset there is an issue with sensors or PC board. Find replacement PC board. Potential freeze conditions.

What should the water temp be on a Lay-z-spa?

The Lay-Z-Spa is not designed to operate with water temperatures exceeding 40ºC (104ºF). Unplug the pump and plug it back in once the water temperature has reached 38ºC (100ºF) or lower. IMPORTANT: Before you restart the pump, press the reset button.

What are the error codes on the spa side?

Flow Switch (heater is deactivated. Pump may also be deactivated). Panel sensors have been pressed too many times in a short period of time. Circuit Board temperature has exceeded acceptable limit. Freeze protection. No action is necessary. Freeze protection. No action is necessary. Communication between the panel and circuit board is faulty.

Gradually add and dissolve 0.5kg (500g) of Pure Spa Salt at a time. Start the Salt Chlorinator System. Allow the spa pump to run on either the 5 hour or 8 hour setting. If the E11 error code is visible again, place a further 0.5kg (500g) of Pure Spa Salt in the spa. Water Leakage.

The Lay-Z-Spa is not designed to operate with water temperatures exceeding 40ºC (104ºF). Unplug the pump and plug it back in once the water temperature has reached 38ºC (100ºF) or lower. IMPORTANT: Before you restart the pump, press the reset button.

How do you remove stopper caps from Lay z spa?

Remove the black stopper caps from the inside of the liner before heating, filtering or running the bubbles on the spa. If you are unsure how to remove them, please refer to the assembly section within the Lay-Z-Spa owners manual. Remove the filter cartridge from the filter housing and check it is clean.

Is there a big list of Spa error codes?

Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble. Problem is, there’s not much consistency among the error codes used by different spa pack manufacturers. Each company uses its own conventions for naming the various system faults.