Rigid insulation has an R-value of up to 6.5 per inch, but it also can be an effective vapor retarder. … Rigid foam board, especially foil-faced polyisocyanurate, creates a vapor-impermeable barrier, so the wall would have limited drying potential.

Is a vapor barrier needed with rigid foam insulation?

Foam insulation usually does not require a vapor barrier. For some foam insulation types, such as closed-cell spray foam and foam board insulation, the insulation itself stops the movement of most water vapor.

What insulation does not need a vapor barrier?

Low-Density Polyurethane Spray Foam Blocks the movement of air (eliminating the need for a vapor barrier), absorbs sound like a sponge, and flexes with the seasonal movement of the framing. Must be professionally applied. Although not flammable, must be protected from fire with drywall or plaster.

Is rigid insulation an air barrier?

Rigid insulation provides thermal protection and it can also serve as an air and moisture barrier. There are three primary types of rigid insulation: expanded polystyrene (EPS), extruded polystyrene (XPS), and polyisocyanurate (polyiso).

What insulation has a built in vapor barrier?

You can buy batt and roll insulation with a built-in vapor barrier made of kraft paper or foil, or you can buy it “unfaced” (without a vapor barrier) and install one separately. A vapor barrier is necessary to prevent moisture absorption, which lessens the ef- fectiveness of the insulation.

Is XPS foam a vapor barrier?

XPS is manufactured in both an unfaced form or with different plastic facings. However, XPS is considered a vapor retarder, not a vapor barrier. … Innovative applications of EPS and XPS have improved a building’s envelope thermal performance.

Is Foamular a vapor barrier?

An insulating sheathing keeps the wall stud cavity warmer. Warmer air and surfaces are less likely to experience condensation than colder air/surfaces at any given level of humidity. So, FOAMULAR® insulating sheathing, that is also semi-permeable, is not a “double vapor retarder” concern.

What is the difference between an air barrier and a vapor barrier?

Air Barriers Provide Superior Moisture Protection for a Home Over Vapor Barriers. Air barriers are designed to prevent the flow of air, and the moisture attached to it, from entering a building envelope. A vapor barrier only aims to prevent the transport of moisture by vapor diffusion into a home’s building envelope.

Is rigid foam insulation waterproof?

Technically, EPS and XPS rigid foam board insulation are considered to be water-resistant. A product branded as waterproof means that it offers complete impermeability, even if permanently immersed in water.

What type of insulation is waterproof?

Waterproof rigid insulation is used on roofs. Expanded polystyrene, or XPS, extruded polystyrene, or EPS, and polyisocyanurate, or polyiso, are the three main types of rigid, closed-cell insulation materials.

Article first time published on

How do I know if I need a vapor barrier?

A vapor barrier is likely required if the building is cladded with absorptive material and if the structure is in United States climate zones 4C, 5 through 8. If you are building in a colder climate, check local laws or consult with your architect if a vapor barrier is required.

When should you not use a vapor barrier?

You may find that vapour barriers are often not required in warmer climates. And, if installed in the wrong climate or on the wrong side of building materials, a vapour barrier can cause more harm than good. This circumstance may prevent water vapour from drying, which in turn can cause rot and mold.

What happens if I don't use vapor barrier?

If water vapor diffuses or infiltrates into the wall cavity and finds the cool surface, moisture problems can occur. Of course, you can have moisture problems here even without the exterior vapor barrier because of what Bill Rose calls the rule of material wetting.

Can you use 4 mil vapor barrier?

Barricade’s 4-mil plastic sheeting is a multipurpose film perfect for a wide variety of construction or DIY projects. This medium-duty plastic sheeting is commonly used as a vapor barrier in between insulation and drywall, used as a drop cloth or a temporary cover for equipment and supplies.

Does insulation have a vapor barrier?

Vapor barriers applied over the face of the insulation provide additional benefits in the fight against moisture. Usually composed of a thin film, such as polyethylene, vapor barriers are used to retard or prevent water vapor diffusion into a wall, ceiling or floor during the cold winter.

Does Rockwool insulation need a vapor barrier?

Note that rock-wool insulation only comes un-faced, meaning there’s no kraft-paper or foil barrier. Depending on the situation, you may need to install an independent permeable membrane to serve as a vapor barrier.

Does rigid insulation need to be covered?

Rigid foam insulation, whether it is expanded or extruded polystyrene, does have to be covered if it is installed in the interior of a building. … Because this type of insulation is made from plastic, it is combustible and may give off highly toxic fumes when burning.

Can you put rigid foam insulation between studs?

Even with its flaws—namely, its inability to perfectly mold to the bays between the studs—rigid foam insulation will be a better bet than no insulation. Using low-expanding spray foam sealant to seal those gaps further increases rigid foam’s insulating properties between studs.

Is rigid foam breathable?

Rigid foam insulation is increasingly becoming the go-to solution for improving a home’s R-value and meeting tougher building-code standards on minimum insulation values. … It meets the air-leakage requirements of the 2010 NBC, providing a breathable layer of insulation with a durable film for easy installations.

Is XPS vapor permeable?

Therefore, 1 inch of XPS is considered to be vapor semi-permeable, while 2 inches is considered to be vapor semi-impermeable.

Does vapor barrier go above or below slab insulation?

The industry consensus is that underslab vapor barriers should be installed if the slab will be in conditioned space, or if the slab will be covered with a moisture sensitive flooring system.

Is rigid foam insulation mold resistant?

Foam insulation is mold resistant but NOT mold-proof. Mold resistance of foam insulation products: This document provides information about the cause, detection, and hazards of mold growth in foam insulating materials in comparison with fiberglass insulation in residential and light-commercial buildings.

What is the difference between pink and blue foam board?

Both are manufactured using the same process and contain similar chemical components. The two products also have the same insulating power. However, blue foam boards are manufactured by Dow Chemical Co. whereas the pink foam boards are manufactured by Owens Corning company.

Does rigid insulation absorb water?

Wrapping Up Unfortunately, laboratory results do not always tell the whole story when it comes to rigid foam insulation performance. While XPS and polyiso rigid foam insulations absorb less water over the course of a 24-hour submersion, they hold that water much longer than their EPS counterpart does.

Is drywall a vapor barrier?

The permeance of unpainted drywall is very high, generally between 20 and 90, so it’s not a vapor retarder at all. … Nearly 100 times as much water vapor goes through the hole in the drywall by air leakage than goes through by diffusion.

Is WRB a vapor barrier?

As I wrote in a recent article on controlling liquid water, the liquid water control layer is also called the drainage plane or the water-resistive barrier (WRB). The water vapor control layer is also called a vapor retarder or vapor barrier.

What is the R-value of rigid insulation?

The R-value is about R-5. Like polyiso, this type of rigid foam won’t absorb water and is stronger and more durable than expanded polystyrene, so it’s probably the most versatile type of rigid foam.

What is XPS insulation?

Extruded polystyrene insulation or XPS Insulation is manufactured through an extrusion process. … This produces a closed cell rigid insulation. Expanded polystyrene insulation or EPS insulation is manufactured using a mould to contain small foam beads.

Does foil backed plasterboard act as a Vapour barrier?

Foil backed plasterboard’s are the same as a standard plasterboard, except for a thin layer of foil that is applied to the back of the board. This foil sheet acts as a vapour barrier, it is intended to stop moisture from penetrating through the boards.

Where should vapor barrier be installed?

Vapor barriers are usually best installed on the side of the wall that experiences the hotter temperature and moister conditions: the inner surface in colder climates and the outer surface in hot, humid climates.

Is Kraft faced insulation a vapor barrier?

Kraft-faced insulation includes a paper vapor retarder, which helps prevent mold and mildew. Kraft-faced insulation should be installed in exterior walls, exterior basement walls, and attic ceilings by pressing the product into the wall cavity with the paper side facing outward, towards the installer.