Pull up on the brake pedal and if the lights go out, switch mis-alignment or pedal position error is the likely cause. The final possibility is a wire shorted to power. Unplug the brake-light switch and if the lights stay on, a short circuit is the case. Finding such a shorted-circuit, is best left to a professional.

How do you know if your brake light switch is bad?

1. Your Brake Lights Don’t Light Up. Your brake lights are supposed to turn on when you push down on the brake pedal, giving a heads up to the driver behind you. …
2. Brake Lights Stay On Continuously. …
3. Bad Cruise Control. …
4. Car Won’t Turn On. …
5. ABS Warning Light Comes On.

Why my brake lights wont turn off?

A common cause for car brake lights that won’t turn on is a faulty brake light switch. This component can be found beneath your dash attached near the brake pedal. If your lights are disabled, it may be sticking closed or the part has failed.

Does a brake light switch have a fuse?

If your lights don’t illuminate on either side and your brake light switch is good, then the next thing to check is the brake light fuse. Locate your vehicle’s fuse box, which is usually under the hood or on the kick panel inside the passenger compartment. … If it has, replace it with a fuse of the same resistance.

How do I know if my brake lights are working?

To test your brake lights and tail lights, get in your vehicle and turn on the ignition switch. You do not have to actually crank your engine. First, check your tail lights by turning on your headlights. If working properly, they will come on simultaneously and glow red.

Which fuse controls the brake lights?

The stop lamp fuse is in the left kick panel inside the vehicle. It is a 15amp fuse that powers the stop light switch on the brake pedal. The brake light switch sends power to rear brake lights.

Is the brake light and turn signal the same bulb?

There are two filaments in each light bulb. One is for your brake light and one is for your turn signal. So when you’re stopped with your turn signal on one filament stays on while the other blinks. … So when this bulb burns out it elimnates your turn signal AND brake light.

Why are my brake lights working but not my tail lights?

The most common reason why your tail lights are not working but brake lights are is due to a bad or wrong type of light bulb installed. It can also be caused by a blown fuse, bad wirings, or corroded sockets or plugs. A faulty control light switch could also be to blame.

Where is the brake light relay located?

A brake light switch is a small electrical relay attached to the brake pedal. It is typically installed above the brake pedal and (hopefully) activated every time your pedal is pressed.

Can you fix a brake light yourself?

Changing a faulty brake light is something anyone can learn to do. A replacement bulb costs about $10, and replacing it on your own will save about $20 in labor and the time it takes to travel to the shop and wait for the work to be done.

Article first time published on

Where is the brake pedal switch located?

The switch is located right near the tip of your right foot near the brake pedal, so it’s easy to access. The switch may actually snap into place without the use of any tools at all. $20-50 dollars should cover the labor costs on most cars.

Why is my brake lights not working after replacing bulbs?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). … Choose the new bulbs of the same type and wattage.

What would cause the brake lights to stay on?

The most common cause your brake lights stay on is because of a faulty brake light switch or sensor. It can also be caused by a faulty brake pedal or a malfunction in the electrical system. If you recently replaced the rear light bulbs when it occurred, you may have installed the wrong light bulbs.

Why are my brake lights on when car is off?

If your brake lights are staying on with the vehicle off, the most common cause is a broken brake light switch or brake light switch stopper.

Are brake lights on top or bottom?

The turn signals are amber in color. The tail/stop lights are red on the bottom ones.

How can you tell if a tail light bulb is bad?

As noted above, once per week, take a few minutes during your day or evening to check if all brake lights are working. If the parking lights work (meaning the rear lights that turn on when the headlights are active), but when pressing the brake light the light does not work, have the tail lamp bulb replaced.

Do brake lights need a relay?

You only need a Brake-Lite Relay if you’re installing a supplemental towed vehicle braking system that pushes or pulls the brake pedal. With the engine off, step on your brakes. If the brake lights do not illuminate, you do not need a Brake-lite Relay.