The ridge cap, the course of shingles on the very ridge of the roof, can be made from available 3-tab shingles. Two simple cuts create three pieces that can be used to finish the shingle project.

Can I use regular shingles for ridge cap?

Overall, architectural shingles would work well as ridge caps since they are extremely resistant to almost every element of weather and can blend well with the other shingles of your roof.

How do you cap architectural shingles?

Place and bend the shingle over the ridge and fasten with a capped roofing nail 1” up and in from the end and edges of the end without roofing cement. Overlap successive shingles so the nail heads are covered and so that the exposed ridge shingle width is consistent along the ridge.

Do you need ridge cap shingles?

Since so much water flows through the roof valleys, they must be protected by extensive roof flashing networks to keep your roof dry and leak-free. With the peaks, a special covering called a ridge cap must be used. Asphalt shingle roofing will typically also have asphalt ridge caps.

Can you put a metal ridge cap on shingle roof?

There are two types of metal ridge vents that you can use for a roof. The first one being a shingle-ver vent and an aluminum vent. Both of these types of vents can be installed on shingle roofs.

Which way does a ridge cap go?

Generally on a north/south orientation, the south end of the ridge would be the place to start. On an east/west orientation, the east end will be the starting point. This is the point on the roof that you will attach the first ridge cap.

How do you put a ridge cap on a metal roof?

1. Run a strip of sealant tape the full length of the ridge, about 1” above your chalk line. …
2. Run closure strips the length of the ridge, interlocking them end to end as you go, and pressing them down on top of the sealant tape.

How many shingles do I need for a ridge cap?

You can cap about 35 lin.ft. of ridge or hips with each bundle of three-tab shingles that come three bundles to the square. You can also salvage waste shingle pieces and portions of damaged shingles for use as caps.

How much does it cost to replace a roof vent?

Installing a roof vent costs between $300 and $650 on average, including labor and materials. Exact rates depend on the type, size, and number of units you choose to install. Ridge vents cost $2 to $3 per linear foot. Roof vents come in a variety of styles and range from $10 to $500 each.

How wide is a ridge cap shingle?

TimberTex® Premium Ridge Cap Shingles offer excellent protection at high-stress areas of your roof (the hips and ridges). Its 12” (305 mm) wide design works with most ridge vents.

Article first time published on

How does ridge cap work?

A ridge vent is an air exhaust vent installed on the peak of a roof. When installing this vent, an air slot is first cut in the roof deck at the roof’s peak. … As the air in the attic heats up, convection helps push the air to the peak of the roof where it escapes through the ridge vent.

What is a shingle ridge cap?

Ridge cap shingles are specifically designed to fit the ridges of roofs. That’s why they are typically pre-bent and thicker than regular roof shingles, which tend to crack when folded over the ridge. The form of the ridge cap shingles also makes them more efficient in shedding water and debris.

What is the purpose of a ridge cap?

A ridge cap fits over the joint between these two edges to keep rain and snow out of the home. It also helps to finish off the look of the roof by creating a tightly sealed joint along the two sides. Pre-fabricated roof caps may be used when workers are installing roofing systems.

Should ridge vent go all the way across roof?

If you’re wondering whether a ridge vent should go all the way across a roof, it depends. You don’t want to cut ridge vents all the way to the edge, but you can install vent caps all the way to the edge. … Ridge vents on metal roofs can be installed in a similar fashion.

What is a roof hip cap?

Ridge Caps are metal objects that cap the ridge of a roof. They are also referred to as ridge rolls or ridge flashings. Ridge Caps are available in standard style options: 3″, 4″, 5″.

Which ridge vent is best?

The shingle-over-ridge vent is a nicer, more consistent look compared to the aluminum vents, which are very susceptible to leaks further down the road because all of the fasteners are exposed—they go right through the surface of the vent and into the roof decking.