Your bowling ball span is the measured distance between the placement of the gripping holes used to hold the ball. The span refers commonly to the distance from the front edge of the drilled thumb gripping hole to the front edges of the two finger gripping holes.

What is span on a bowling ball?

Span. The span refers to the distance from the front edge of the drilled thumbhole to the front edges of the two finger holes.

How should your thumb fit in a bowling ball?

Check your thumb You want your thumbhole to feel loose, but it needs to be tight enough that you can release the ball without gripping it. You shouldn’t need more than a piece of tape to accomplish this.

How do you measure the diameter of a bowling ball?

Place the left measuring contact of the micrometer (the side without the dial) just below the point marked with the grease pencil on the bowling ball in step 2. The top of the measuring contact should be just below the mark, but not on the mark.

How far should your thumb be in the bowling ball?

6. The thumb must be inserted into the thumb hole of the ball down to the second knuckle joint as to allow the ball surface to rest on the palm of your hand and with the full extension of your thumb.

What Grip Do Pro Bowlers use?

Virtually all professionals use the fingertip grip, however, so if you have aspirations of bowling at a high level, a successful fingertip grip is something you’ll want to aspire to.

How do you measure your finger grip on a bowling ball?

Insert the middle and ring fingers into the holes. The holes should fit the finger tips and release the fingers with little friction. This is the size of your finger holes.

What are the dimensions of a bowling ball?

“Regulation bowling balls are 8 ½ inches in diameter and weigh 8 to 16 pounds.” What are the Different Types of Bowling Balls? wisegeek.com. “Ten-pin bowling balls are typically eight and a half inches in diameter and contain three finger holes.

How do you measure a ball size?

One easy way to measure the “size” of a ball is how far it is from side to side. Your tennis ball example is a good one: a typical tennis ball is about 2.5 inches form side to side. And one way to measure that size is to place the ball on a table in the sunlight when the sun is nearly overhead — close to noon.

What is the size of a standard bowling ball?

USBC specifications include physical requirements for weight (≤16 pounds (7.3 kg)), diameter (8.500 inches (21.59 cm)—8.595 inches (21.83 cm)), surface hardness, surface roughness, hole drilling limitations (example: a single balance hole including the thumb hole for “two-handed” bowlers), balance, plug limitations, …

Article first time published on

What is an asymmetric bowling ball?

An asymmetrical core is a ball where the RG values of the Y and Z axes of the ball differ by more than 5%. It’s generally accepted that symmetrical drilled balls have a smooth, controllable motion. … Asymmetrical balls can exhibit large amounts of track flare even with long pin-to-PAP (positive axis point) distances.

What does the dot on a bowling ball mean?

Bowling-Ball Pins Explained Not to be confused with the pins at the end of the lane, every bowling ball is marked with a colored dot, which represents the ball’s pin. The pin is vital in determining how to drill your ball to get your desired reaction on the lanes.

What pound ball do pro bowlers use?

Most pro bowlers use 16-pound balls, although more than you think use 15-pounders. Another method is to add one or two pounds to the weight of the house ball you normally use. A heavier ball drilled specifically to your hand will seem to weigh about the same as a house ball two pounds lighter. .

Should I get inserts for my bowling ball?

Finger inserts are not necessary if you are a new bowler and are preparing to have your first bowling ball drilled. Finger inserts are only useful in a fingertip grip drilling. If you are getting your first new ball drilled as a conventional grip drilling, there is no need for inserts.

Which fingers go in a bowling ball first?

Not only is that wrong it isn’t going to make it easy to throw a high scoring game and it may just hurt your fingers a little bit as the ball will always want to roll off the side of your hand. To safely hold a bowling ball you should always use your middle and ring finger and not your index finger!

Which fingers go in the bowling ball?

Your middle and ring fingers should each be in their hole up to the second knuckle. The fingertip grip is for more experienced bowlers. You still fully insert your thumb, but your middle and ring fingers are only inserted up to the first knuckle.

Do Pro Bowlers use finger holes?

Bowling balls are only permitted one balance hole. … “It is not necessary to have a thumb hole if the bowler isn’t going to use it for gripping purposes and the ball has to be within our static balance requirements to be used during USBC certified competition.”

What is a thumb slug in a bowling ball?

Thumb slugs are actually known by a number of names including: inserts, solids, and of course, slugs. No matter what you call them, they are all the same. Typically made of vinyl or urethane, they are a solid piece of material that is placed in the thumb hole of your bowling ball.

What is fingertip bowling?

In a fingertip grip, the span of the hand is fitted to the last joint of the index and middle finger, while the conventional grip is fitted to the middle joint. The cornerstone of bowling is maximizing the engagement of the ball with the lane by maximizing friction to create a hook.

What is a throw called in bowling?

From Wikipedia, the free encyclopedia. In the sport of ten-pin bowling, there are many different ways in which to deliver (known as a “throw” or “roll“) the bowling ball in order to advance it toward the pins in an accurate and powerful manner. Generally, there are three basic forms of 10-pin bowling.

How long does it take for a bowling ball to be drilled?

First ball they should spend at least 40- 1 hr with you. Make sure you are buying the right one for you. More experienced bowlers, a lot quicker.

How do you know if your bowling ball is drilled properly?

After your new ball is drilled and the holes are beveled, contoured, and shaped to fit your gripping fingers and thumb, the new ball should fit like a glove without much looseness in the fingers or thumb holes.

How much does it cost to have holes drilled in a bowling ball?

Custom drilling services can cost anywhere from $50 to $70. Installation of finger inserts, thumb slugs, switch grips, and thumb molds are also available for custom drilled bowling balls. This service is recommended for the recreational bowler who would like to own their own bowling ball.

What is the average size of an exercise ball?

Exercise ball diameterPerson’s height45 cm5′ and under55 cm5’1″– 5’8″65 cm5’9″– 6’2″75 cm6’3″– 6’7″

What is the diameter of a 65cm exercise ball?

CHOOSE YOUR BALL SIZEHeightBall Size5’0″ to 5’5″Small: 55cm/22″5’6″ to 5’11″Medium: 65cm/26″6’0″ to 6’3″Large: 75cm/30″

What is the best instrument that measures the distance around a ball?

A spherometer is an instrument used for the precise measurement of the radius of curvature of a sphere or a curved surface.

How do you read bowling ball specs?

The circumference of a bowling ball 13 lbs. or greater is 26.7″ minimum, 27.002″ maximum. The diameter of a bowling ball 13 lbs. or greater is a minimum of 8.5″ and a maximum of 8.595″. The Radius of Gyration of a 13 lb. ball or greater is a minimum of 2.46″ and a maximum of 2.8″.

How big is a 10 pin bowling ball?

Ten-Pin Bowling Balls have a diameter of 8.595” (21.83 cm) and circumference of 27” (68.58 cm). The mass of a Ten-Pin Bowling Ball is between 10-16 lb (4.54-7.26 kg).

How heavy is a 10 bowling ball?

The diameter of the ball must be constant. The circumference of a ball shall not be more than 27.002 inches nor less than 26.704 inches, nor shall it weigh more than 16 lbs (there is no minimum weight).

Why are there different sizes of bowling balls?

If you haven’t noticed, all of the sizes we’ve mentioned are tied to specific bowling game types, meaning that most of the sizes are subject to regulations and specifications that are tied to those games. This is, of course, the case with ten-pin bowling balls.

What Motiv Bowling balls are asymmetrical?

• Hammer Black Widow 2.0 Bowling Ball. Rated 5.00 out of 5. …
• Motiv Jackal Ghost Bowling Ball. …
• Storm Proton PhysiX Bowling Ball. …
• Motiv Jackal Flash Bowling Ball. …
• Roto Grip Rubicon UC2 Bowling Ball. …
• Motiv Jackal Legacy Bowling Ball. …
• Storm Dark Code Bowling Ball. …
• Radical Results Bowling Ball.