How do I test my Intelli vent?
Andrew Davis How do I test my Intelli vent?
1 Check wiring to the hot surface ignitor – replace ignitor assembly if wiring is damaged or worn. 2 Check ignitor assembly plug and the socket on the Intelli-Vent™ body for good connection. Replace ignitor assembly and/or control if necessary. 3 Check resistance of ignitor at room temperature (77°F) at the plug end.
How do I reset my Intelli vent water heater?
1 Manual reset is accomplished by first, turning off power to the water heater for 10 seconds. 2 Restore the power to the water heater. 3 Within 10 seconds of restoring power, press the two temperature adjust buttons simultaneously until the left (green) “Vacation” LED begins to blink (approx.
How do you relight a Richmond water heater?
How to Light the Pilot Light on Richmond Water Heaters
- Step 1: Turn Off the Gas Control.
- Step 2: Turn the Control to Pilot.
- Step 3: Light the Pilot Flame.
- Step 4: Turn the Dial to the On Position.
- Step 1: Set the Thermostat to the Lowest Setting.
- Step 2: Clear Out Residual Gas.
- Step 3: Turn On the Power and the Gas Control.
Why does my hot water heater keep going into vacation mode?
Just the vacation light is on. That’s not a brand or model. If the water heater is doing this then you have a fault condition and another LED has to be lit. If not then the gas control valve needs to be replaced.
Should I turn my hot water tank off when I go away?
Unless you’ll be vacating your home for a month or longer, turning off your water heater is unnecessary.
What do you need to know about the Intelli vent?
INTELLI-VENT TROUBLESHOOTING GUIDE Technical Training Department Ashland City, Tennessee © 2005 1 of 24 INTELLI-VENT™ FEATURES The Intelli-Vent™ is a combination control incorporating all temperature control, ignition control, blower and ignitor control, flame sensing, and gas regulation into a single device. Advanced Diagnostics – Error Codes
What are the Erro codes on Intelli vent?
Advanced Diagnostics – Error Codes The Intelli-Vent™ features advanced diagnostics with 15 specific error codes including reversed polarityand inadequate groundingnotification. Diagnostic information is conveyed via 6 LED lights on the control. These erro r codes will help diagnose and repair the wate r heater quickly and accurately.
When to replace the Intelli-vent pressure switch?
then on again to clear the error code – if the error code persists replace the Intelli-Vent™ control. 4 Pressure switch circuit remains open longer than 5 seconds after the blower is energized. Blower may run continuously in this condition. 1 Ensure the blower is running – check for 120 VAC to
How to turn off Intelli vent water heater?
1Plug in water heater and turn on power. All lights on the control will come on for about 1 – 5 seconds. All lights will then turn off. If the stored water is above 70°F (residential) and the control setting has not been increased from it’s factory setting, nothing more will happen.
INTELLI-VENT TROUBLESHOOTING GUIDE Technical Training Department Ashland City, Tennessee © 2005 1 of 24 INTELLI-VENT™ FEATURES The Intelli-Vent™ is a combination control incorporating all temperature control, ignition control, blower and ignitor control, flame sensing, and gas regulation into a single device. Advanced Diagnostics – Error Codes
Advanced Diagnostics – Error Codes The Intelli-Vent™ features advanced diagnostics with 15 specific error codes including reversed polarityand inadequate groundingnotification. Diagnostic information is conveyed via 6 LED lights on the control. These erro r codes will help diagnose and repair the wate r heater quickly and accurately.
How to fix an open ignitor on an intelli vent?
The Intelli-Vent™ control has detected an open ignitor circuit. 1 Check wiring to the hot surface ignitor – replace ignitor assembly if wiring is damaged or worn. 2 Check ignitor assembly plug and the socket on the Intelli-Vent™ body for good connection. Replace ignitor assembly and/or control if necessary.
1Plug in water heater and turn on power. All lights on the control will come on for about 1 – 5 seconds. All lights will then turn off. If the stored water is above 70°F (residential) and the control setting has not been increased from it’s factory setting, nothing more will happen.
