You may like the look of pressure-treated wood but you should think ahead before you use it. … When using the new Pressure-treated wood – ACQ and CA, keep in mind that they do have a higher concentration of copper, which results in a chemical reaction that discolours and corrodes aluminum and some metal fasteners.

Can you use pressure treated wood with aluminum?

Does Treated Wood Corrode Aluminum? Yes. Most of the new chemical treatments contain copper and should never come in direct contact with aluminum. Total failure caused by corrosion can occur in less than a year.

What metal can be used with pressure treated wood?

The treated wood industry has recommended the use of stainless steel and hot-dip galvanized (HDG) fasteners and connectors for years.

Does pressure treated react with aluminum?

The Short Answer: A Barrier Membrane between the aluminum and pressure treated plywood. As long as the aluminum is not directly touching the pressure treated plywood, you will not experience any corrosion or reaction between the two.

Can you use aluminum flashing with pressure treated lumber?

Never use galvanized steel or aluminum flashing in contact with an ACQ pressure-treated wood ledger board because it will corrode. … Copper works well because it is compatible with the chemicals used in commonly sold ACQ-treated lumber and is easy to bend.

Can you use treated wood on aluminum boats?

Pressure treated wood products are not a one-use-fit-all category. … The use of EcoLife with aluminum products was specifically tested on residential flashing. Viance highly recommends that you contact the boat manufacturer for the proper repair for your boat.

Can I wrap treated wood with aluminum?

You can’t wrap treated wood on your porch or screen room in aluminum. … If so, count on replacing it in a few years after the chemicals from the treated wood cause a chemical reaction with the aluminum and it starts to corrode and flake away.

Does pressure treated wood corrode metal?

Pressure treated wood is a popular product for outdoor construction, i.e. bridges and decks. … When wood treated with the new chemicals was exposed to metal parts, the metal tended to corrode, even moreso in water contact environments, in only a few years.

Does ACQ corrode aluminum?

For aluminum fasteners, ACQ is more than seven times more corrosive than CCA I and more than five times more corrosive than CCA II.

Can you use treated plywood on aluminum trailer?

As said above, NO MANUFACTURER USES MARINE OR TREATED PLY ON THIER ALUMINUM TRAILERS. The issue is called galvanic corrosion and as said above by ajax is because treated lumber is high in copper. This is the same reason that the axle is supposed to be isolated from the aluminum frame beams.

Article first time published on

Can I use zinc with pressure treated wood?

3.1 Fasteners for preservative-treated wood. Fasteners for preservative-treated wood shall be of hot dipped zinc-coated galvanized steel, stainless steel, silicon bronze or copper.

Does stainless steel react with pressure treated wood?

Pressure treated wood is most commonly used for construction in areas exposed to harsh outside conditions. … There are only two recommended corrosion resistant systems which should be used with pressure treated wood: hot-dip galvanized steel and stainless steel fasteners and industrial consumables.

Does galvanized metal react with pressure treated wood?

Recommendations on Fasteners for Treated Wood The protective coating on electroplated galvanized fasteners is too thin and will perform poorly, and common nails will corrode rapidly after fastening most copper-based treated wood.

Should I wrap pressure treated lumber?

And because these new wood treatments are especially corrosive to aluminum, it’s best to use vinyl or copper flashing, or to wrap the wood in a protective rubberized membrane. … Allow treated wood to dry thoroughly before staining or painting. Test dryness by sprinkling the wood’s surface with water.

What happens when you cut pressure treated wood?

When Southern pine lumber is pressure-treated, the waterborne preservative forms a permanent bond with the wood’s fiber. Sawdust produced by cutting or machining pressure-treated wood is not hazardous to people, plants or pets. When sawing or machining treated wood, wear eye protection, a dust mask and gloves.

Can you put vinyl siding over treated wood?

On existing houses, old vinyl or metal siding must be removed, but vinyl can be installed over old wood siding without removing it. Installing vinyl over wood siding does require considerable preparation and also may require adjusting window and door frames for a wider wall..

What does ac2 stand for in lumber?

Alkaline Copper Quaternary (also known as ACQ) is a water based wood preservative method recently introduced in countries where there is a demand for alternatives to Chromated copper arsenate (CCA).

Can vinyl flashing be bent?

Aluminum and vinyl make effective siding. A siding brake bends aluminum or bendable vinyl siding to the angles you want using leverage from a hinged joint. … This method is recommended for do-it-yourself siding repair or other small projects.

Can you use pressure treated wood for boats?

Pressure-treated plywood and lumber do a good job for their intended purpose. But for boat repair and building, I would shy away from them. By using WEST SYSTEM Epoxy with marine-grade or non-pressure treated exterior-grade plywood, you can make economical, long-lasting repairs to your boat.

What kind of wood is used for boat decks?

It’s essential that timber used for marine construction is hardy and durable. It cannot be too soft, nor too brittle, and of course it must stand against decay over time. There are plenty of options out there, and some of the most common wood types used for boats include cedar, ash, mahogany, oak, and pine.

Can I use treated plywood on my pontoon boat?

Treated Plywood Pros: Has been used for years for boats, resists insects, water damage, rot, algae and fungi, it’s a good base for floor covering and it’s durable overall.

What are the different types of pressure treated wood?

There are many types of treated lumber. There are three main families of treated lumber used in construction: Borate, Alkaline Copper Quat (ACQ) and other rot-resistant treatments, and non-combustible (Non-Com).

What kind of wood should I use for a trailer?

Rough oak is used for trailer decking primarily for its strength. Oak is one of the only decking materials recommended for use with tracked equipment such as skid steer loaders and excavators. In the trailer industry, oak decking is referred to as “rough” oak for a reason.

What is CCA plywood?

A. CCA is pressure-impregnated preservative treated lumber and plywood designed for long-term performance in various commercial or industrial and limited residential applications where protection from fungal decay and termites is required.

Is Treated lumber corrosive?

Using pressure-treated lumber (PT) in home construction is very effective in reducing wood destroying insect activity, but it has the adverse effect of causing corrosion on most hardware and fasteners.

Does copper react with treated lumber?

For steel connectors and fasteners, copper is the enemy in PT lumber. But copper is not the only metal that will react with steel to cause fastener corrosion.

Why can't you use joist hangers with treated lumber?

Construction Concerns: Pressure-Treated Lumber and Joist Hangers. The chemicals used in pressure-treating lumber, including fire-retardant chemicals, are corrosive to bare steel. The joist hangers used in construction with both sawn lumber and manufactured joists are usually galvanized (zinc-coated).

Will AC2 corrode aluminum?

Approved for Aluminum Contact AC2® pressure treated products are approved for aluminum contact while other treatments available today are not because of their corrosiveness. Corrosive treatments, such as, ACQ are not only bad for aluminum but can also prematurely corrode other metal fasteners.

What is CDX plywood?

CDX Plywood is used primarily by contractors to build exterior walls and roofs. CDX plywood has one side veneer grade “C” and one side veneer grade “D”. The two are bonded together with glue which can withstand a little moisture. The APA would recognize CDX Grade Plywood as C-D Exposure 1 plywood.

What kind of wood is used for utility trailer floors?

Pressure treated Pine flooring is the most commonly used wood flooring material in trailers. The abundant supply of Pine wood in the south coupled with its sturdy nature make for a solid basic flooring choice.

Can you use drywall screws in treated lumber?

It is a very bad idea to use dry wall screws with treated lumber. There are certainly ASTM codes which set out the coating specifications for certain types of fasteners to be used with ACQ treated lumber. … They should also come back and remove the drywall screws and replace them with an ACQ compatible screw.