The most common alternative to using joist hangers is a ledger strip. … The ledger strip must be able to support the weight of the joists while not tearing out of the wall it has been secured to. The ledger strip can be secured to the outside wall by using screws or nails when securing to wood studs.

Can you build a deck without joist hangers?

The most common alternative to using joist hangers is a ledger strip. … The ledger strip must be able to support the weight of the joists while not tearing out of the wall it has been secured to. The ledger strip can be secured to the outside wall by using screws or nails when securing to wood studs.

Do you need joists for decking?

A decking joist is a repeated board used as the structural base for your deck frame that is attached to the ledger via galvanized joist hangers. Typically, joists run perpendicular to the house, while the decking on top runs parallel to the house. Every significant portion of your deck needs to be supported by a joist.

Does decking need hangers?

If you install them properly, joist hangers will keep your decks and floors strong as wood dries, twists, shrinks and ages. … So the next time you hold a square dance or weight-lifting contest on your deck, you’ll rest easier knowing you used joist hangers and installed them the right way.

How far apart should joists be on a deck?

Deck joist spacing should never exceed 16″ on center (with the exception of MAX deck boards, which allow for maximum 24″ on center). For a more rigid feel, 12″ or less may be preferred. If adding additional framing, be sure to keep all boards level and in plane across the tops.

Can I use joist hangers for floor joists?

Joist hangers not only simplify the framing process but also strengthen the deck or floor you are building. When hanging floor joists, use joist hangers to make building a floor deck simpler. Place hangers every 16 inches on center. Position each hanger using the tab to hold it in place.

What is the purpose of a joist hanger?

Joist Hangers, as the name suggests are designed to hold timber joists in place. They are used to anchor things like decking, floors and ceilings. Most joist hangers wrap around three sides of a wooden beam and nails or screws are put into the holes to keep it in place.

Can I use 4x2 for decking joists?

4 x 2 Timber Rail / Joist These decking joists are the most common sized framing timber for decking. They provide a solid structure for fixing your decking boards too. When making your decking frame you should use a 400mm spacing between your timber joists.

Should deck joists be 2x6 or 2x8?

For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. … Most decking is not strong enough to support longer spans than 16″.

How far can I span a 2x8 for a deck?

Using this rule, a 2×6 will span 9 feet, a 2×8 will span 12 feet, and a 2×10 will span 15 feet. As you can see, the larger the depth, the longer the span.

Article first time published on

How far can a 2x6 joist span without support?

A 2×6 can support up to 50 pounds per square foot of weight without sagging with a maximum span of about 12 feet when spanning a distance horizontally, with the 2×6 standing in a vertical position. This number includes both live and dead weight.

Can I use 2x8 for deck joists?

2×8 for joists will be fine, with 16″ OC. Should use 2×10 for beams but 2×8 will be fine as well. If you are worried you can triple the 2×8 for the beams but double will be sufficient. You should put the beams at 7 and 14 feet out from the house, with the piers you should do 3 per beam with spacing of 1, 7, 13.

Should deck boards run parallel or perpendicular to house?

Decking running parallel to the house makes the deck look wider and blends the deck into the house. If the decking runs perpendicular, the deck looks long and extending far out, away from the house.

How many footings do I need for a deck?

Before starting to build, the first question is: How many footings do I need for a deck? For an attached 12 x 12′ deck, you’ll need at least 3 footings, plus at least 2 more if you’re planning on building stairs with it. If your deck will be a different size, it’s easy to figure out how many you’ll need.

Which direction should deck boards run?

On most decks, the decking boards run parallel to the house and across the joists (either perpendicular or at a 45 degree angle).

How much weight can joist hanger support?

Joist SizeMin Capacity lbs2×64002×85002×106002×12700

Do joist hangers work?

Q. The carpenter that built my deck used joist hangers to hold up the joists along the house and at the end of the deck. The biggest problem I’ve seen with joist hangers of all types is if the wrong nails were used when installing them. …

Do you need a double rim joist on a deck?

It is advisable to increase the rigidity and strength of your deck’s rim or perimeter in order to reduce bounce and provide a solid foundation for your rail system. This can be accomplished in a couple of ways. You may want to install double rim joists across long sections to respond to the flexibility of the material.

Do you use joist hangers on both ends?

Joist hangers are preferable to both toe-nailing and end-nailing. Joist hangers provide greater shear force support to joists, as the hanger allows for both face nailing and toe-nailing into ledger boards and rim joists.

Can I Sister deck joists?

Sistering joists is commonly used when adding onto an existing deck or repairing a deck. … The side-by-side joists should be attached together by a nailing pattern similar to combining boards to form a beam. If you are adding onto a deck, you must make sure the footings are large enough to support the added loads.

Can 2x6 be used for deck joist?

You can use 2×6 as deck joists if the deck is low enough to the ground as not to require guard railing. When using S-P-F 2×6 deck joists, the span must not be greater than 9’0″ (2.73m) with joists at 16″ o.c. (400mm), and 9’10” (3.01m)with spacing at 12″ (300mm).

Can I use 2x8 for deck boards?

Q: Can I use 2×8 treated lumber as deck boards? A: No, that’s a not a good idea. Lumber wider than 6 inches should not be used as a flat surface. Wide, flat boards have a tendency to pool rain water, which can lead to cupping problems.

Can I use 2x6 for deck boards?

Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.

What would I use for decking frame?

In general, pressure-treated timber is one of the best options for decking frames due to its cheap cost. Softwoods, such as Cedar and Redwood, are good choices for framing as well, especially if you want a more sustainable and safer option.

Can you use 4x4 for deck joists?

For most decks, 4×4 lumber is strong enough for structural posts. If a deck is raised more than 6 feet above the ground, codes may require 6×6 posts.

Can you use 3x2 for decking base?

3×2 can be used but you’ll have to support it more frequently throughout its length, say every five feet or so.

Can a 2x8 span 16 feet?

Span is determined by species, grade, dimensions, spacing, use, and load. A rule of thumb is 1.5 times a joist’s depth but in feet when spaced at 16” centers. In general, a 2×8 will span 1.5 x 8, so 12-feet. Based on all factors though, a 2×8 joist span is 7′-1” to 16′-6”, and a rafter 6′-7” and 23′-9”.

How much load can a 2x8 support?

Span (feet)Weight Supported (lb)2 x 2″ x 6″2 x 2″ x 8″42250469061680313082660

Can I use deck pier blocks instead of footings?

Pier blocks can be used instead of footings for a ground-level deck not requiring permits. Piers blocks can also be used if the frost level depth is less then the height of the pier block.

How much weight can a 2x6 deck support?

According to the Codes, a 2×6 on edge with the weight pressing through 5.5” of wood will support approximately 53lbs per linear foot. So, an 8-foot length will support about 424lbs. However, a short span 2×6 on edge can support between 600 and 900lbs depending on wood species, grade, and other factors.

What is the maximum span for a 2x6 floor joist?

The maximum distance a 2×6 can span, according to the 2018 IRC, for a floor joist, is 12′-6”, ceiling joist 20′-8”, rafter 18′-0”, deck board 24”, deck joist 9′-11”, deck beam 8′-3”, and 6′-1” as for header. Always check the codes for determining factors or consult a Structural Engineer.