Are there any problems with the Kenmore water softener?

Another common concern we get calls about often is that people tell us that water is about half way up their salt tank. If you have this issue there is something wrong with your water softener. The good news is that usually if you have this issue it can be fixed easily.

What to do if your water softener is full of water?

If your water softener is full of water, another potential solution is to change the Kenmore water softener float setting. The water softener float valve controls the water levels in the brine tank. If it is set too high, excess water may build up, and your unit may not be able to release all the water after each discharge cycle.

Where is the seal on a Kenmore water softener?

The rotor valve seal is located on the bottom of the rotor valve. This seal stops water from leaking out of the valve and lets the water flow through the opening at the bottom of your rotor valve. The seal may wear out over time and it will start to leak. If this happens, then it will need to be replaced.

What does error code 1 on Kenmore water softener mean?

Error code #1, meaning a valve motor failure, is one of the more common codes you will have displayed. If your Kenmore water softener display is showing Error Code #1, you can try the following: Step 1: Unplug your softener and then plug it back in.

Another common concern we get calls about often is that people tell us that water is about half way up their salt tank. If you have this issue there is something wrong with your water softener. The good news is that usually if you have this issue it can be fixed easily.

The rotor valve seal is located on the bottom of the rotor valve. This seal stops water from leaking out of the valve and lets the water flow through the opening at the bottom of your rotor valve. The seal may wear out over time and it will start to leak. If this happens, then it will need to be replaced.

If your water softener is full of water, another potential solution is to change the Kenmore water softener float setting. The water softener float valve controls the water levels in the brine tank. If it is set too high, excess water may build up, and your unit may not be able to release all the water after each discharge cycle.

Why is my Kenmore Salt Tank half full?

Solution: The most common reason for the salt tank being half full of water is that the nozzle and venturi are dirty or blocked. This is a process that Kenmore provides instructions on how to do on your own at

How much salt do you need for Kenmore water softener?

No DIY skills necessary. All you have to do is fill in the tank with around 200 pounds of regenerating salt. Once, you have done this, it will immediately and automatically start processing your soft water. Another key benefit of this is that you don’t have to worry about device maintenance.

What is error code 3 on Kenmore water softener?

Kenmore Error Code #3: If you are getting an Error code 3, it may be that the switch (pictured below) needs replacing. Here are the steps to replace this switch: Step 1: Unplug the unit. Step 2: Remove the lid of your softener so you can see the motor.

No DIY skills necessary. All you have to do is fill in the tank with around 200 pounds of regenerating salt. Once, you have done this, it will immediately and automatically start processing your soft water. Another key benefit of this is that you don’t have to worry about device maintenance.

Kenmore Error Code #3: If you are getting an Error code 3, it may be that the switch (pictured below) needs replacing. Here are the steps to replace this switch: Step 1: Unplug the unit. Step 2: Remove the lid of your softener so you can see the motor.

Where is the inlet on a Kenmore water softener?

Check that all of the Kenmore water softener’s tubes are connected properly if you notice poor water output. Make sure the inlet pipe from your main water pipe to the Kenmore appliance, located on the top back of the softener, is plugged in.

Why is the timer on my water softener not working?

The timer is an electronic control board that allows you to program your water softener and lights up the display. It also controls the water softening and resin filter flushing processes. If it isn’t working, it will need to be replaced. Step 1: Put on work gloves and unplug your water softener from its power source.

What is the automatic salt tank light on Kenmore water softener?

Its automatic salt tank light (LED) informs you when and if the tank needs replenishment with new softener salt. There is also a larger LCD screen, which displays all the settings in a way that can be visible in low light conditions. Tested and certified by National Sanitation Foundation (NSF). 3. Kenmore Water Softener 38350 – 31,000 Grain

Error code #1, meaning a valve motor failure, is one of the more common codes you will have displayed. If your Kenmore water softener display is showing Error Code #1, you can try the following: Step 1: Unplug your softener and then plug it back in.

What to do if your water softener regenerates too often?

If it seems like your softener is regenerating too often, a professional can modify the settings or make needed repairs. If service and/or parts are required, make sure to have your softener manufacturer’s warranty handy.

Check that all of the Kenmore water softener’s tubes are connected properly if you notice poor water output. Make sure the inlet pipe from your main water pipe to the Kenmore appliance, located on the top back of the softener, is plugged in.

If it seems like your softener is regenerating too often, a professional can modify the settings or make needed repairs. If service and/or parts are required, make sure to have your softener manufacturer’s warranty handy.

Solution: The most common reason for the salt tank being half full of water is that the nozzle and venturi are dirty or blocked. This is a process that Kenmore provides instructions on how to do on your own at

How to install the Kenmore genius water softener?

SECTION 1 SAFETY GUIDES CHECK LIST OF STEP-BY-STEP GUIDES TO INSTALL PROGRAM THE TIMER SANITIZING THE WATER SOFTENER FILL THE STORAGE TANK WITH SALT SECTION 2 FACE PLATETIMER FEATURES SOFT WATER SERVICE AND REGENERATION SECTION 3 SALT: REFILLING KEEPING THE WATER SOFTENER KEEP THE SOFTENER HELPFUL HINTS CHECKLIST…

How does water flow in a Kenmore genius?

Water flow is directed nozzle and venturi, draws brine from the salt storage tank and injects it into the resin bed via the bottom distributor. SECTION 5 5C. WATER FLOW THROUGH THE SOFTENER VALVE soft water to valve outlet During FAST RINSE, the rotor & disc is positioned resin tank through distributor, to the drain.

How to do diagnostics on Kenmore Genius 2?

If an Error code shows, the #1 SELECT button to enter the diagnostic Press the ON/OFF-HOLD button and hold in for 3 seconds. Page 25 SECTION 5 Before working on the valve, turn off the water supply and disconnect from electrical RELIEVE PRESSURE: VALVE BYPASS: Close the inlet valve soft water faucet. Then close the outlet the bypass valve.

Why is my Kenmore water softener not producing water?

If you cannot produce water, call your water utility company as they may have turned off your water or reduced pressure due to problems such as local construction in your neighborhood. Verify that the Kenmore water softener is plugged into a reliable electrical outlet if its front panel display won’t turn on or if it shuts down randomly.

Its automatic salt tank light (LED) informs you when and if the tank needs replenishment with new softener salt. There is also a larger LCD screen, which displays all the settings in a way that can be visible in low light conditions. Tested and certified by National Sanitation Foundation (NSF). 3. Kenmore Water Softener 38350 – 31,000 Grain

Where is the rotor valve on a Kenmore water softener?

You should contact a professional to do this for you. The rotor valve directs water through your water softener during the water softening cycle and while flushing the resin filter. The rotor valve seal is located on the bottom of the rotor valve.